I know this has been mentioned before but when I searched through the forum I couldn't find the thread What the problem is when I place down a GNER MK4 Coach in surveyor I get the following script error. Can some kind soul please help me on how to get rid of the said script error please
Here is the screenie of the script error:
Peter Hicks MK4's
- Nexusdj
- Forum Veteran
- Posts: 3097
- Joined: Sun Dec 12, 2010 3:02 pm
- Trainz Version: TRS22
- Trainz Build: 123794
- Author KUID: 45317
- Location: West Midlands
- Contact:
Re: Peter Hicks MK4's
Check the config to make sure that they're not set up as an engine ,
Check the script file and make sure it says :
if it say Locomotive change it to "Vehicle" but make sure you use a capital "V"
***Note that the entry mk4ic_po will be different for each coach***
Code: Select all
engine 0
Code: Select all
class mk4ic_po isclass Vehicle
***Note that the entry mk4ic_po will be different for each coach***
High visibility pixels must be worn when on or about the line !!
-
- R.I.P
- Posts: 354
- Joined: Sun Dec 12, 2010 3:34 pm
- Trainz Version: TS2009
- Trainz Build: 41844
- Location: Trowbridge, Wiltshire
Re: Peter Hicks MK4's
Done that and all is as you say it should be so I am at a loss
- Nexusdj
- Forum Veteran
- Posts: 3097
- Joined: Sun Dec 12, 2010 3:02 pm
- Trainz Version: TRS22
- Trainz Build: 123794
- Author KUID: 45317
- Location: West Midlands
- Contact:
Re: Peter Hicks MK4's
Okay no probs , Plan B ....
Whats the kuid or kuids of the coaches that are flagging up the errors ?
What dependencies do they use ?
At some stage I have fixed peters Mk4's but I can't remember what I did (the script as a loco is always my first port of call these days) .
Thinking about it I believe (though I could be wrong) that Peters Mk4's have to be marshalled in the correct order so that the coach letter script works correctly .
I think there's a marshalling list on his website ?
Whats the kuid or kuids of the coaches that are flagging up the errors ?
What dependencies do they use ?
At some stage I have fixed peters Mk4's but I can't remember what I did (the script as a loco is always my first port of call these days) .
Thinking about it I believe (though I could be wrong) that Peters Mk4's have to be marshalled in the correct order so that the coach letter script works correctly .
I think there's a marshalling list on his website ?
High visibility pixels must be worn when on or about the line !!
- alexfleming380
- Past 500!
- Posts: 519
- Joined: Mon Sep 26, 2011 6:48 pm
- Trainz Version: TS12
- Trainz Build: 61388
- Author KUID: 622162
- Location: That wee hilly place above England
Re: Peter Hicks MK4's
Class 91 Loco - TOE - TO - TO - TO - TOD - SV - PO - PO - PO - DVTNexusdj wrote:Thinking about it I believe that Peters Mk4's have to be marshalled in the correct order so that the coach letter script works correctly .
Hope this helps ya
Alex
Please, call me Alex.
Formerly known as afleming97
Formerly known as afleming97
-
- R.I.P
- Posts: 354
- Joined: Sun Dec 12, 2010 3:34 pm
- Trainz Version: TS2009
- Trainz Build: 41844
- Location: Trowbridge, Wiltshire
Re: Peter Hicks MK4's
That is correct I did place them down in that order, thanks for your response though
- Shippy2013
- Past 100!
- Posts: 128
- Joined: Sat Apr 02, 2016 10:04 am
- Trainz Version: TS12
- Trainz Build: 61383
- Location: Nottinghamshire
Re: Peter Hicks MK4's
Sorry to bump an old thread but saves starting a new one for a similar topic.
I’ve created a route that is based on the GCR through Nottingham assuming it didn’t close and basing it on the Chiltern Railways model of operations. I want to use rakes of Mk4’s cascaded off the ECML for expresses between Sheffield Victoria and London Marylebone as it solves the disability access law, also as I liked the old GNER Libery and as the GCR was part of the LNER not to far fetched to have GNER as the routes operator!. (Nobody has produced plug door mk3’s yet). This is were I hit a problem.
As mentioned here unless you marshal the Mk4’s as a 2+9 set in the correct order it bugs because of the letter script. Is there any way of deleting or disabling this part of the script allowing a 2+6 formation of Class 67, TOE, TO, TO, TOD, SV, PO and DVT.
I thought I’d found a way of tricking the script by marshalling the rake correctly then deleting the unwanted coaches. Worked fine until a point in the AI programme were the consist changes direction and the bug is back.....
Help appreciated thanks.
I’ve created a route that is based on the GCR through Nottingham assuming it didn’t close and basing it on the Chiltern Railways model of operations. I want to use rakes of Mk4’s cascaded off the ECML for expresses between Sheffield Victoria and London Marylebone as it solves the disability access law, also as I liked the old GNER Libery and as the GCR was part of the LNER not to far fetched to have GNER as the routes operator!. (Nobody has produced plug door mk3’s yet). This is were I hit a problem.
As mentioned here unless you marshal the Mk4’s as a 2+9 set in the correct order it bugs because of the letter script. Is there any way of deleting or disabling this part of the script allowing a 2+6 formation of Class 67, TOE, TO, TO, TOD, SV, PO and DVT.
I thought I’d found a way of tricking the script by marshalling the rake correctly then deleting the unwanted coaches. Worked fine until a point in the AI programme were the consist changes direction and the bug is back.....
Help appreciated thanks.